Litter-Robot 3 Pinch Contact & Dfi Kit (2024)

Table of Contents
1. Litter-Robot 3 Pinch Contact & DFI Kit 2. Litter-Robot 3: Pinch & DFI kit installation guide 3. Litter-Robot 3 Open Air DFI Hardware (v2) - RobotShop 4. Litter-Robot™ III DFI Kit including pinch detectors - Cat Evolution 5. Litter-Robot 3 Pinch Contact 6. Still showing Pinch Detect after replacing terminals - Robot Parts 7. Litter-Robot Replacement Parts | Litter-Robot Repair 8. Litter-Robot III Open Air DFI Hardware - RoboCleaners 9. Best Quality Litter-Robot 3 Pinch Contact & DFI Kit - catlittersale.com FAQs References

1. Litter-Robot 3 Pinch Contact & DFI Kit

  • Purchase replacement pinch contact and drawer full indicator (DFI) circuit board assembly for your Litter-Robot 3.

See details ›

2. Litter-Robot 3: Pinch & DFI kit installation guide

  • The DFI and anti-pinch safety feature share the same assembly. Learn how to replace the DFI board assembly and pinch contacts below.

  • Find easy steps to install your Litter-Robot 3 DFI Kit. Explore our comprehensive guide.

See details ›

3. Litter-Robot 3 Open Air DFI Hardware (v2) - RobotShop

See details ›

4. Litter-Robot™ III DFI Kit including pinch detectors - Cat Evolution

  • Purchase replacement infra red Drawer Full Indicator circuit boards and assembly for your Litter-Robot 3. Includes DFI board assembly, DFI perspex covers.

  • Litter Robot 3 infrared Drawer Full Indicator circuit boards and assembly Kit for a blue flashing light issue. Kit includes DFI board assembly, DFI housing, mounting screws, Pinch Detectors.

    See Also
    Fifteen Years Republic Of China Sun Yat Sen Commemorative Gold Coin

See details ›

5. Litter-Robot 3 Pinch Contact

  • The Litter-Robot 3 pinch contact allows your Litter-Robot to be assembled correctly. Purchase a replacement pinch contact for your Litter-Robot 3.

See details ›

6. Still showing Pinch Detect after replacing terminals - Robot Parts

  • Jul 23, 2021 · ... pinch are making strong contact. ... This video can help you replace it: Litter-Robot 3 DFI Kit + Pinch Detect Terminals Installation - YouTube.

  • I’ve been having intermittent issues for years with the pinch detect, but now it seems to be broken for good. If I reset it, it goes to flashing blue as if the tray is full, and resetting again puts it back to the rapidly flashing yellow light–I’m stuck between the two. After taking the unit apart I found that the pinch terminals were very corroded. I ordered new ones and replaced them, but the problem still remains. I confirmed with a multimeter that the two prongs in the anti-pinch are making ...

See details ›

7. Litter-Robot Replacement Parts | Litter-Robot Repair

  • Litter-Robot 3 Key and Plug Kit. $15. Rating ... Litter-Robot 3 Pinch Contact & DFI Kit. $30.

  • Keep your automatic litter box working for years to come with Litter-Robot replacement parts and refresher items. Use our DIY repair guides and videos.

See details ›

8. Litter-Robot III Open Air DFI Hardware - RoboCleaners

  • Please contact our customer service for advice, guidance or modification of orders. Right to cancel and warranty. You have total peace of mind and can enjoy ...

  • Litter-Robot III Open Air DFI Hardware

See details ›

9. Best Quality Litter-Robot 3 Pinch Contact & DFI Kit - catlittersale.com

  • Get the best in fashion and fine for All the people at catlittersale.com, with free shipping on orders over 34$.

See details ›
Litter-Robot 3 Pinch Contact & Dfi Kit (2024)

FAQs

What is the DFI error on the Litter-Robot 3? ›

Check for obstructions blocking the drawer full indicator (DFI) sensors. There are two sensors inside the base, above where the waste drawer would sit. Debris, such as dust or cat fur, can interfere with the DFI sensor. This can cause the unit to inaccurately trigger a drawer-full indication.

Tell Me More ›
How do you clean an anti pinch sensor Litter-Robot? ›

Remove the waste drawer and set aside. The pinch sensor is located in the base. Look at the top of the base, and locate the plastic pinch bar on the left side of the waste port opening. Press the bar inward several times to dislodge any built-up litter or debris.

Read The Full Story ›
Why is my Litter-Robot blinking blue and red? ›

If the unit detects an issue with all three laser sensors, called curtain sensors, it will indicate a fault with the entire system and the light bar on the Litter-Robot will display red and blue alternating lights. You will also receive a notification on your phone if you use the Whisker app.

Discover More ›
How do you reset the Litter-Robot pinch detect? ›

Short press the Reset button, then short press the Cycle button to run a Clean cycle. After the test cycle, Litter-Robot should be in the Home position displaying a blue light bar.

Get More Info ›
How do you replace pinch contacts in Litter-Robot? ›

Install New Pinch Detect Terminals

Using needlenose pliers, position the new pinch contacts. A flathead screwdriver can help to gently push them into place. Make sure the contacts are fully seated in the slot. Both metal pinch contacts should be touching each other.

Learn More ›
What is a pinch sensor? ›

A pinch sensor is designed to measure the force on a rolling window.

View Details ›

References

Top Articles
Make-up » Dekorativkosmetik
Studentvue Ccboe Login
Latest Posts
Kim jesteś w świecie Jujutsu Kaisen?
Jujutsu kaisen kim jesteś
Recommended Articles
Article information

Author: Sen. Ignacio Ratke

Last Updated:

Views: 6148

Rating: 4.6 / 5 (76 voted)

Reviews: 83% of readers found this page helpful

Author information

Name: Sen. Ignacio Ratke

Birthday: 1999-05-27

Address: Apt. 171 8116 Bailey Via, Roberthaven, GA 58289

Phone: +2585395768220

Job: Lead Liaison

Hobby: Lockpicking, LARPing, Lego building, Lapidary, Macrame, Book restoration, Bodybuilding

Introduction: My name is Sen. Ignacio Ratke, I am a adventurous, zealous, outstanding, agreeable, precious, excited, gifted person who loves writing and wants to share my knowledge and understanding with you.